Samtec Technology/Software

Sr. Hardware Test Engineer

Taipei, Taiwan In person Full-time

Job title:Sr. HW TEST ENGINEER

Summary/Objective: The Sr. hardware (HW) Test Engineer owns electrical and high-speed hardware test for Samtec optical products, namely on-board optical engines and modules such as the FireFly™ family, in vertical-cavity surface-emitting laser (VCSEL)-based multimode and silicon photonics (SiPh) variants and including optical PCI Express, and pluggable optical transceivers built with original design manufacturer (ODM) partners.

The role develops electrical, high-speed signal, and control-interface test methods and automated test stations for engineering validation and production, correlates results across the Samtec Taiwan lab, Samtec manufacturing sites, and original design manufacturer / contract manufacturer (ODM/CM) production test, and isolates hardware failures efficiently. It requires strong knowledge of component behavior, circuit operation, signal integrity (SI) and power integrity (PI), digital signal processor (DSP)/microcontroller unit (MCU) control interfaces, and high-speed serial link test methodology.

Essential Functions/ Responsibilities

  • Develop electrical and high-speed hardware test plans, test limits, test flows, and validation methods for optical engines and transceivers, from engineering validation test (EVT) and design validation test (DVT) through production release.
  • Characterize and validate electronic components and interfaces, including DSPs and retimers, MCUs, power management integrated circuits (ICs), clocks, electrically erasable programmable read-only memory (EEPROM), sensors, laser-driver and transimpedance amplifier (TIA) electrical interfaces, and protection circuits; read and analyze schematics, power trees, transmit/receive (Tx/Rx) electrical paths, control interfaces, clock/reset circuits, and high-speed signal paths, and feed findings back to the design team.
  • Perform electrical testing: voltage, current, module power, power sequencing, ripple/noise, inrush current, clock, reset, control signals, and interface timing.
  • Perform high-speed electrical Tx/Rx characterization at 28G non-return-to-zero (NRZ) and 56G/112G/224G four-level pulse amplitude modulation (PAM4) per lane: bit error ratio (BER), eye diagram, jitter, forward error correction (FEC) statistics, clock and data recovery (CDR) behavior, transmitter finite impulse response (FIR) and receiver continuous-time linear equalizer and decision feedback equalizer (CTLE/DFE) equalization, and loopback testing.
  • Perform or support SI/PI characterization of modules, host boards, and fixtures: insertion loss, return loss, impedance, time-domain reflectometry (TDR), crosstalk, and S-parameters.
  • Validate module management and control functions: inter-integrated circuit and management data input/output (I2C/MDIO) communication, EEPROM and memory maps, alarms and warnings, reset and low-power states, module state-machine behavior, and firmware–hardware interactions, per Common Management Interface Specification (CMIS) for pluggable transceivers and Samtec interface definitions for on-board optics.
  • Build, integrate, maintain, and troubleshoot high-speed test platforms: bit error ratio testers (BERTs), real-time and sampling oscilloscopes, vector network analyzers (VNAs), TDR instruments, host and evaluation boards, fixtures, cables, and Ethernet-switch or PCI Express host platforms.
  • Develop and maintain automated test software, instrument control, data logging, limit management, traceability, and reporting in Python, LabVIEW, C#, or equivalent.
  • Perform test correlation, measurement system analysis and gauge repeatability and reproducibility (MSA/GR&R), reference-plane verification, cable and fixture de-embedding and loss compensation, calibration control, and golden-sample management across the Samtec Taiwan lab, Samtec manufacturing sites, and ODM/CM production test.
  • Analyze test data and isolate failures among device hardware, components, circuits, firmware settings, SI/PI, fixtures, cables, instruments, software, environment, and manufacturing process; drive closure with design, product, and quality engineering.
  • Improve test time, retest rate, false-failure rate, test coverage, station stability, and production test capability; support test deployment and transfer to Samtec manufacturing sites and ODM/CM partners.
  • Mentor engineers and technicians and establish hardware test lab practices and documentation.
  • Participate in reviewing and responding to suppliers' specification responses, waiver/deviation requests, test reports, root cause analysis (RCA) reports, process change notifications (PCNs), and related technical documents, with focus on electrical, high-speed hardware, and test impacts.

“The responsibilities as defined are intended to serve as a general guideline for this position. Associates may be asked to perform additional tasks depending on strengths and capabilities.”

Experience / Qualifications (Ideal Candidate Profile)

These qualifications describe the ideal candidate profile; candidates with a strong partial match may also be considered during initial screening.

  • Bachelor's degree or above in Electrical Engineering, Electronics Engineering, Communications Engineering, or a related technical discipline.
  • Ideally, 5+ years of hardware test, or hardware design and validation, experience on high-speed optical modules, transceivers, serializer/deserializer (SerDes) or physical-layer device (PHY) devices, or similar high-speed electronic products.
  • A strong understanding of electronic components, analog/digital and power circuits, control interfaces, and high-speed serial links is preferred.
  • Working knowledge of NRZ/PAM4 signaling, BER, FEC, jitter, eye diagrams, CDR, equalization, SI, and PI.
  • Ability to read schematics and troubleshoot hardware with oscilloscopes, BERTs, VNAs, TDR instruments, and equivalent laboratory equipment.
  • Working knowledge of DSP, MCU, power IC, clock, EEPROM, sensor, driver/TIA electrical interfaces, and module control functions.
  • Experience developing automated test with Python, LabVIEW, C#, C/C++, or equivalent programming environments.
  • Strong debugging, data analysis, failure isolation, and root cause analysis skills are preferred; good written and verbal English communication skills.

Preferred Experience / Desired Skills

  • Experience with 400G, 800G, or 1.6T optical transceivers, on-board or mid-board optical engines, or other 112G/224G PAM4 platforms; VCSEL-based multimode and SiPh products are both relevant.
  • Experience with CMIS, I2C/MDIO, module evaluation boards, Ethernet-switch/BERT platforms, and PCI Express (Gen 5/Gen 6) host and link testing.
  • Experience with S-parameter, TDR, insertion loss, return loss, crosstalk, and high-speed fixture and cable characterization and de-embedding.
  • Experience with test correlation, MSA/GR&R, guard banding, measurement uncertainty, and production test deployment, including transfer to ODM/CM partners.
  • Knowledge of optical module architecture and the electrical-to-optical interaction among DSP/retimer, driver, laser, photodiode (PD), and TIA; able to run combined electrical/optical debug with the optoelectronic (OE) test engineer.
  • Self-motivated, well organized, and able to work independently and cross-functionally with teams in Taiwan, the United States, and partner sites.
  • Ability and willingness to travel domestically and internationally as needed.

Training required

  • On-the-job training as appropriate.
  • Product-, process-, test-, quality-, and safety-specific training as required by assigned responsibilities.

Job description provided by Samtec.
View the original posting